 Posted: Tue Sep 20, 2011 7:19 pm |
 |
|
| Alfredo Prada |
| Member |
|
| |
| Joined: 20 Sep 2011 |
| Posts: 16 |
| Location: Las Vegas, USA |
|
|
 |
|
|
| I am following the Ease tutorial and when I get to the adding windows section, pg 78 of Advanced Modeling techniques. I can add the windows using both the displace/duplicate and extrude methods, the problem is they dont
coat to the wall surface, I followed the instructions and verified the settings
but I get the windows in the middle off the room and not on the wall.
Please help, I am trying to complete the tutorial and eventually take the Ease
classes.
thanks |
|
|
_________________
Alfredo Prada |
|
|
|
| Posted: Tue Sep 20, 2011 10:05 pm |
|
|
| Tim |
| Member |
|
| |
| Joined: 11 Feb 2008 |
| Posts: 61 |
| Location: Canberra ACT, Australia |
|
|
|
|
|
| Alfredo,
Just checking... in the Face properties box, did you check/tick the "is coat of" option and select the appropriate Face # to coat?
Regards |
|
|
_________________
Tim Kuschel
GUZ BOX design + audio |
|
|
|
| Posted: Tue Sep 20, 2011 10:19 pm |
|
|
| Alfredo Prada |
| Member |
|
| |
| Joined: 20 Sep 2011 |
| Posts: 16 |
| Location: Las Vegas, USA |
|
|
|
|
|
| Yes, I followed the tutorial several times, I cant figure out the problem, again I checked the settings recommended on the tutorial.
I will try again tomorrow
thanks |
|
|
_________________
Alfredo Prada |
|
|
|
| Posted: Wed Sep 21, 2011 8:05 am |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Alfredo,
Is the window face a Two-Fold Face? You can check it on the face properties. It must also be oriented correctly. It's orange side pointing towards the inside of the room.
Also, I'm not sure what you mean with "I get the windows in the middle of the room and not on the wall". Maybe you are a bit confuse regarding the coordinates?
HTH, |
|
|
|
|
| Posted: Fri Sep 30, 2011 10:08 pm |
|
|
| Alfredo Prada |
| Member |
|
| |
| Joined: 20 Sep 2011 |
| Posts: 16 |
| Location: Las Vegas, USA |
|
|
|
|
|
| Hello, Yes the face is two fold. I dont know about proper orientation (it is not mentioned on the tutorial , pg 78 of Advanced Modeling techniques). How do I change the orientation? the orange side is pointing towards the outside. |
|
|
_________________
Alfredo Prada |
|
|
|
| Posted: Sat Oct 01, 2011 11:19 am |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Hi Alfredo,
To invert a face just select it and use the Invert Face tool or press I. It is mentioned in the Chapter 3 - Constructing a model  |
|
|
|
|
| AFMG Network Forum Index -> EASE 4 |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT
Page 1 of 1
|
|
|
|
|
