 Posted: Fri Aug 24, 2012 6:21 pm |
 |
|
| yphs_mst |
| Member |
|
| |
| Joined: 27 Apr 2007 |
| Posts: 12 |
|
|
|
 |
|
|
| Hi all,
I may miss this information in the manual or somewhere, but I cannot find how to do this. Once, I used RME UFX which mic input starts at channel 9. Systune recognized the first 8 channels. How do I change the 8 input channels recognized by Systune to input 9-16 of the sound card?
Hadi |
|
|
_________________
Hadi Sumoro |
|
|
|
| Posted: Fri Aug 24, 2012 6:27 pm |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Dear Hadi,
The Channel Map feature is available for Systune PRO users under the main menu Configure > Channel Map.
A window will open where you can assigned the channels.
Best Wishes,
Pedro Lima |
|
|
|
|
| Posted: Fri Aug 24, 2012 6:44 pm |
|
|
| yphs_mst |
| Member |
|
| |
| Joined: 27 Apr 2007 |
| Posts: 12 |
|
|
|
|
|
|
| Hi Pedro, thank you for the prompt reply. It is available in Pro version only, then that is the reason I cannot find this. Thank you again. |
|
|
_________________
Hadi Sumoro |
|
|
|
| Posted: Mon May 27, 2013 7:15 am |
|
|
| lvsoundtech |
| Member |
|
| |
| Joined: 27 May 2013 |
| Posts: 2 |
| Location: Nevada |
|
|
|
|
|
| I have an RME Fireface UFX as well and was hoping to be able to use it with Sysune. So does this mean that without the "Pro" version I will be unable to use the Mic inputs from my RME interface? |
|
|
|
|
| Posted: Mon May 27, 2013 2:17 pm |
|
|
| AFMG Pedro Lima |
| Forum Moderator |
|
| |
| Joined: 05 Jun 2010 |
| Posts: 269 |
| Location: Germany |
|
|
|
|
|
| Maybe an alternative might be rerouting the Mic Input to channel to one of the line output channels and then link it back to a line input ( from 1 to 8 ). This loop back might be made with a small cable or internally within the RME software.
Not sure if the UFX is capable of the internal (in-software) loopback, though. I know Fireface 400 is.
HTH,
Pedro |
|
|
|
|
| Posted: Tue May 28, 2013 1:42 pm |
|
|
| hadisumoro |
| Member |
|
| |
| Joined: 01 Oct 2007 |
| Posts: 39 |
| Location: USA |
|
|
|
|
|
| Yes, you can route the output of the mic (output 9-12) to analog 1-4 output, and then use the loopback function in the ASIO mixer. Systune will be able to see the signal at channel 1-4.
Hadi |
|
|
|
|
| AFMG Network Forum Index -> AFMG SysTune |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT
Page 1 of 1
|
|
|
|
|
