| reference loop in sys tune |
 Posted: Thu Feb 12, 2009 11:28 am |
 |
|
|
| I rode in the user manual that systune is able to us the output of the sound card (without reinject it an in input) for reference. I use a d audio sound card and it seems to not work (IR found are udge). any clue???
thanks |
|
|
|
|
| reference loop in sys tune |
| Posted: Thu Feb 12, 2009 1:39 pm |
|
|
| Waldemar |
| Member |
|
| |
| Joined: 05 Dec 2005 |
| Posts: 112 |
|
|
|
 |
|
|
| Olivier,
SysTune can use the digital origin for the played signal for the refrence for the calculation of an Impulse Response if you select [Out].
If you select [1], then the input at [In1] is the reference. |
|
|
_________________
Best Regards
SDA, Waldemar Richert |
|
|
|
| Posted: Thu Feb 12, 2009 4:15 pm |
|
|
|
| I try what u sayd but no good result
olivier |
|
|
|
|
| Posted: Thu Feb 12, 2009 5:25 pm |
|
|
| Jim Mobley |
| Member |
|
| |
| Joined: 27 Jul 2005 |
| Posts: 134 |
| Location: Foothill Ranch, California, USA |
|
|
|
|
|
| Hi Oliver,
Using the output as a reference assumes that the inputs and outputs are clock synchronous. This is true for some sound cards, the EASERA Gateway for example, but many sound cards will require an actual hardware connection. It seems that your D-Audio card is one of them. |
|
|
_________________
Best regards,
Jim Mobley
Sr. Application Engineer
Renkus-Heinz, Inc.
19201 Cook St.
Foothill Ranch, CA 92610 USA
TEL: +1-949-588-9997
FAX: +1-949-588-9514
www.renkus-heinz.com
mailto:jim@renkus-heinz.com |
|
|
|
| Posted: Fri Feb 13, 2009 7:45 am |
|
|
| Waldemar |
| Member |
|
| |
| Joined: 05 Dec 2005 |
| Posts: 112 |
|
|
|
|
|
|
| Hello Olivier,
for the D-Audio Card there is the possibilty to make a shortcut between the Output and the Input by the D-Audio Mixer (by Software).
I think this is what you read.
So you can unse IN2 as the reference for the Mic on IN1. |
|
|
_________________
Best Regards
SDA, Waldemar Richert |
|
|
|
| Posted: Sat Apr 04, 2015 11:42 am |
|
|
| CharlesJk8 |
| Member |
|
| |
| Joined: 04 Apr 2015 |
| Posts: 1 |
| Location: United States |
|
|
|
|
|
| Using the output being a reference assumes the inputs IN ADDITION TO outputs are clock synchronous. It is real intended for some sound cards, your EASERA Gateway with regard to example, but numerous sound CARDS may require an true hardware connection. It seems The idea your current D-Audio CARD will be single connected with them.
_______________________________________________________
casinomagzine
one piece filler arcs
can you work at starbucks at 15 |
|
|
|
|
| AFMG Network Forum Index -> AFMG SysTune |
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT
Page 1 of 1
|
|
|
|
|
